← All guides
For suppliers • Examples

Product carbon footprint examples: how to read and compare them

By • • Updated • 6 min read

Product carbon footprint examples are only useful with their unit, boundary and data attached. Below we walk through a published study of Levi's 501 jeans, show how washing habits change it, and list the fields a supplier's report should carry. We also show how to compare two examples without fooling yourself.

What a product carbon footprint example tells you

A product carbon footprint example is a figure in kg CO₂e for one unit of a product, such as one T-shirt or one pair of jeans. On its own the number says little. You also need the unit, the boundary and the data behind it.

Whole-life examples include washing at home and disposal, which a supplier's own cradle-to-gate figure leaves out. Expect your factory-gate number to be lower than a whole-life example for any garment that gets washed.

Weight, material, factory energy and washing at home move a product's figure the most. Our guides to the carbon footprint of a T-shirt and the carbon footprint of jeans show how the stages add up.

A published example: Levi's 501 jeans

Levi Strauss & Co. published a cradle-to-grave study of its 501 jeans. Its life cycle results deck gives 33.4 kg CO₂e for one pair.

The study covered the 2012 production year, with primary data from 11 supplier factories and 6 fabric mills. It looked at consumers in the United States, the United Kingdom, France and China.

The deck states that an expert panel found the study conforms with ISO 14040 and ISO 14044, the life cycle assessment standards.

Consumer care is the largest phase, at 12.5 kg (37%). Fabric production follows at 9.0 kg (27%), then transport, logistics and retail at 3.8 kg (11%).

Fibre is 2.9 kg (9%), cutting, sewing and finishing 2.6 kg (8%), sundries and packaging 1.7 kg (5%) and end of life 0.9 kg (3%).

Up to the factory, fibre, fabric, making and sundries add to 16.2 kg, about half the total. That is the part a supplier's cradle-to-gate figure would cover.

The pattern is common to garments that are washed: fabric making and home care take the largest shares.

33.4 kg
  • Consumer care 37%
  • Fabric production 27%
  • Transport, logistics, retail 11%
  • Fibre 9%
  • Cut, sew, finish 8%
  • Sundries and packaging 5%
  • End of life 3%
Levi's 501 jeans, cradle-to-grave climate impact by phase (Levi Strauss & Co., The Life Cycle of a Jean, 2015 results deck).

How washing habits change the jeans example

The same deck shows how much the use phase depends on the owner. For one pair worn by an average American over its life, Levi's figures put care at 13.38 kg CO₂e.

Washing after every wear raises that to 30.77 kg. Washing every second wear gives 15.38 kg, every fifth wear 6.15 kg and every tenth wear 3.08 kg.

So the use phase alone can swing by a factor of ten. That is why buyers asking for supplier data want cradle to gate: it leaves out the part the supplier cannot control or measure.

It is also why two whole-life examples for the same product can disagree. Each study picks a washing scenario, and that choice can outweigh everything the factory does.

Lifetime consumer-care climate impact of one pair of Levi's 501 jeans, US consumer, by washing frequency (Levi Strauss & Co. LCA results deck, 2015).

Why examples for the same product differ

Two whole-life figures for the same product can both be right and still disagree. They answer different questions with different data.

The Levi's study is one product, one company and one year, built with factory data and its own washing scenarios. An estimate built from average factors and a standard use profile can land well away from it for good reasons.

This matters when a buyer quotes a published figure back to you. If they set your cradle-to-gate number against a cradle-to-grave study, yours will look small for the wrong reason. Point out the boundary first.

Need a footprint for a buyer?ISO 14067 method, PACT v3 file and a PDF report.
Get free estimate →

What a supplier's footprint report should contain

A footprint report should give the number and everything needed to judge it. Without these fields, a buyer cannot use the figure in their own reporting.

Buyers usually need a cradle-to-gate figure. The GHG Protocol Scope 3 Standard sets cradle to gate as the minimum boundary for purchased goods. The PACT methodology for sharing footprints is cradle to gate as well.

ISO 14067 lists what a footprint report must include. A few values must sit on their own line: fossil and biogenic emissions, land-use change and air freight.

A summary line you can copy: [Product and style code], per [unit], [boundary], based on factory data from [start month] to [end month], calculated to [standard] using [factor sources and versions]; [share]% own data; excludes [items] because [reason].

Every bracket maps to one item in the checklist. If you cannot fill a bracket, the buyer will ask about it.

Here is the line filled in for an imaginary product: Crew-neck cotton T-shirt, style TS-101, per piece of 0.18 kg, cradle to gate, factory data from April 2025 to March 2026, calculated to ISO 14067 with the factor sources listed in annex A; 40% own data; excludes sewing thread under 1% of weight. Every figure in it is a placeholder for yours.

Fields a buyer expects
  • Product and unit, such as one T-shirt or one pair
  • Boundary: cradle to gate or cradle to grave
  • Data period: the 12 months behind the figure
  • Share of each life-cycle stage
  • Fossil, biogenic, land-use change and air freight on their own lines
  • Emission factor sources and versions
  • Share of your own measured data
  • Standard followed and who calculated it
  • Exclusions, each with a reason

How to compare product carbon footprint examples

Compare two examples only when the unit and the boundary match. If they do not, the gap tells you about the method, not the product.

A fair test is like for like. Product carbon footprint examples from a screening tool, a published study and your own calculation can all be right and still disagree.

Run through these checks before you quote a comparison to a buyer:

  • Same unit: a per-item figure and a per-kg figure cannot be compared at all.
  • Same boundary: a cradle-to-grave figure includes washing; a cradle-to-gate one does not.
  • Same stages: check whether packaging and transport are in or out.
  • Same factor sources: different databases give different values for the same fibre.
  • Similar data period: factory energy and grid power change from year to year.
  • Same product type and weight: a heavyweight hoodie is not a light T-shirt.

Turn an example into your own footprint

Use the examples as a range finder, then replace averages with your own factory data. That is the usual path to a figure a buyer will accept.

Sense-check first. If your estimate comes out many times higher than a close published example, look for a unit or weight error before you send it.

A result well below the example deserves the same scrutiny. Missing losses, a forgotten dyeing step or a fibre factor used for finished fabric can all make a footprint look too small.

Paste a product link into the free footprint estimate to see a screening figure. For a figure to send, run a full product footprint with your materials, weights and energy bills. It produces a PDF report and a PACT data file.

Selling hundreds of styles? Upload the whole catalogue instead; the steps are in our guide to footprinting a whole catalogue.

  1. 1
    Find the closest exampleSame product type, unit and boundary
  2. 2
    Get a screening estimateFrom a product link
  3. 3
    Add your own dataMaterials, weights, a year of bills
  4. 4
    Check against the exampleBig gaps usually mean a unit error
  5. 5
    Send the packPDF report and PACT data file
From an example to a footprint for your own product.

Sources and further reading

The studies and standards behind the examples in this guide:

  • Levi Strauss & Co., The Life Cycle of a Jean (LCA results deck, 2015): Levi Strauss & Co.
  • ISO 14067:2018, carbon footprint of products: ISO
  • GHG Protocol Corporate Value Chain (Scope 3) Standard: GHG Protocol
  • PACT Methodology v3: WBCSD PACT
  • PACT Technical Specifications v3.0.3, the data file: PACT docs

Questions

What is an example of a product carbon footprint?

Levi Strauss & Co. published 33.4 kg CO₂e for a pair of 501 jeans, cradle to grave. The figure comes with its boundary, data year and washing scenarios, which is what makes it usable as an example.

What is the carbon footprint of a cotton T-shirt?

It depends on the shirt's weight, its fibre, the factory's energy and how often it is washed. A whole-life figure counts washing at home, so it will be higher than a supplier's cradle-to-gate figure.

Why do footprints for the same product differ?

They use different units, boundaries, data years and factor databases. Washing assumptions alone can change a garment's figure several times over.

How much of a garment's footprint is washing?

It depends on habits. In Levi's 501 study, consumer care was 37% of the total, and lifetime care ranged from 3.08 to 30.77 kg CO₂e by washing frequency.

What should a product carbon footprint report include?

The product and unit, boundary, data period, factor sources, share of own data and the standard followed. It should also list exclusions and show some values on their own line.

Are screening estimates the same as a supplier's footprint?

No. Screening estimates use product listings and average factors. A supplier's footprint uses its own materials, weights and energy bills.

Can I use a published example instead of my own footprint?

Only to sense-check your own figure. A buyer asking for your product's footprint expects one built from your materials and factory data.

Footprints to send your buyersISO 14067 method, a PACT v3 file and a PDF report with every source.
Get free estimate →