per kg of product, raw materials to the factory gate (weight not stated: add it under Change assumptions for a whole-life figure per item) · sold in India · made in India
FIG. 01Where 19.21 kg CO₂e comes from: per kg of product, raw materials to the factory gate. A screening estimate from the listing and published data.
Change anything below and the footprint recalculates. What you change is marked “Stated”. Nothing here is saved.
Sold in
Freight
Materials
Part
Material (kg CO₂e per kg)
Share %
Mass
Source
Biodegradable Cotton
Family word, assumption applied ⓘ
1,000 g
Stated
Primary source
Raw materials26%4.91 kg
Production74%14.30 kg
17.29 kgincluding carbon taken up by plants
0.444 kg Ccarbon held in the product, reported apart from the total (ISO 14067 §6.4.9.3)
10.09–62.97likely range, 95%
In everyday terms, about the same as driving 113 km in a petrol car, 2,401 smartphone charges, or 0.9 tree-years of absorption.
Is this your product?Replace our defaults with your own materials, energy and supplier data. The biggest lever here: run the factory on solar electricity.
Everything behind the figure, for auditors and the curious. Built to the requirements of ISO 14040/44, ISO 14067 and PACT v3.
Standards checkISO 14040/44, ISO 14067 and PACT v3, requirement by requirement
Standards check · ISO 14040/44 · ISO 14067 · PACT v3Screening estimate: not a full footprint study
ISO 14040/14044
Listed calculation checks passed; independent review or verification pending
13 met · 1 justified · 0 not met · 1 need reviewer
ISO 14067
Does not conform
22 met · 1 justified · 1 not met · 1 need reviewer
PACT
Does not conform
15 met · 3 not met · 1 need reviewer
All 30 requirements, with clauses
Requirement
ISO 14040/44
ISO 14067
PACT v3
The study's purpose is written down
Met
§4.2.2
Met
§6.3.1
—
No public claim that one product beats another
Met
§4.2.2; Amd 1 Annex C
Met
§Annex A, Annex B
—
The unit is clear, and a partial footprint is labelled as such
Met
§4.2.3.2
Met
§6.3.3
Met
§3.2.4
The system boundary is described
Met
§4.2.3.3
Met
§6.3.4, 7.3 b
Met
§3.2.3
The time period is stated and justified
—
Met
§6.3.6
Met
§3.2.3
Product category rules are used where they exist
—
Met
§6.2
Met
§3.1.2
Anything left out is small, estimated and reported
Met
§4.2.3.3.3
Met
§6.3.4.3
Met
§3.3.1.2
The data is checked for consistency
Met
§4.3.2–4.3.3
Met
§6.4.3
—
Own processes use measured data, or say why not
—
Met
§6.3.5
Met
§4.1.3
Every database value is referenced and fit for purpose
Met
§4.3.2
Met
§6.3.5
Met
§4.1.3.2
Shared factory burdens are split by the standard rules
Not applicable
§4.3.4
Not applicable
§6.4.6
Not applicable
§3.3.1.4
Recycling is counted with the cut-off method
Met
§4.3.4.3
Met
§6.4.6.3
Met
§3.3.2.2
Electricity covers its whole life cycle
Met
§4.3.2–4.3.3
Met
§6.4.9.4.1
Met
§3.3.2.3
Electricity follows the market-based rules
—
Met
§6.4.9.4.4
Met
§3.3.2.3, Box 7
Land-use change is counted and shown separately
dLUC included but not separable in the factor for m1. Fix: Use a factor with a separate dLUC result, or supply material.land_use_change with its value, source, year and whether the material factor already includes it. A documented no-LUC statement can resolve an unknown coverage gap.
—
Not met
§6.4.9.5
Not met
§3.3.2.4
Biogenic carbon is counted in and out
—
Met
§6.4.9.2, 6.4.9.3, 6.5.2
Met
§3.3.2.4
Air freight is shown separately, without radiative forcing
—
Not applicable
§6.4.9.7
Not applicable
§3.3.2.1
No offsets or avoided emissions
—
Met
§6.3.4.1
Met
§3.3.2.2
Latest IPCC warming factors (AR6, 100 years)
74.5 % of cradle-to-gate emissions use AR5 factors; PACT allows only the latest IPCC report once its grace year has passed. Fix: Replace these factors with AR6-characterised data.
Justified
§4.4.2
Justified
§6.5.1
Not met
§3.2.2
Fossil and biogenic methane are kept apart
—
Met
§6.5.2
—
Key choices are stress-tested
Met
§4.5.3.3
Met
§6.4.5, 6.6
—
Uncertainty is assessed
—
Met
§6.6
—
Data quality is scored
Met
§4.2.3.6
Met
§6.3.5
Met
§4.2.2, 4.2.3
Limitations are stated
Met
§4.5.4
Met
§6.6, Annex A
—
Results are broken down the required way
—
Met
§7.2
Met
§3.3.1, data model
The study report contains every required item
Met
§5.2
Met
§7.3
—
The PACT data file is complete
Missing or invalid: companyIds, productIds. Fix: Add company and product identifiers (URNs such as urn:mfp:company:acme), the reference period and a PACT unit.
—
—
Not met
§6.1; Tech Specs v3.0.3
The primary data share is reported
—
—
Met
§4.2.2
Independent critical review
No critical review recorded. Fix: Commission an ISO 14071 critical review before any public communication; a panel review is mandatory for public comparisons.
Needs reviewer
§6
Needs reviewer
§8
—
Third-party verification of the calculation model
The MFP footprint calculation model has not yet been verified by a third party. Fix: Commission limited-assurance verification of the calculation model (PACT v3 §5.3.3, Tables 14–15).
—
—
Needs reviewer
§5.3.3
These standards apply to studies. This checklist reports the implemented checks; it is not certification or a substitute for independent review. “Needs reviewer” items (critical review, verification of the calculation model) can only be closed by an independent third party.
Assumptions and defaults18 entries, 3 warnings
Warnings · 3
Factor te26_cotton_conv_in includes land-use change that cannot be separated; LUC is reported inside fossil GHG for this line.
Grid electricity uses location-based national or regional averages. PACT v3 and Catena-X require the market-based residual mix where contractual instruments exist; supply electricity_factor for contracted or residual-mix power.
Temporal scores for desnz_2025, textile_exchange_2026 use the edition year; their underlying data are older, so those temporal scores may be better than the data deserve.
Assumptions register · 18 entries
Screening mode: this listing gives no primary data, so every input below that is not a stated material or weight is a named screening default. The result is not PACT-conformant (primary data share 0 %).
The listing states no weight and no typical weight is on file for "home textile", so the footprint is given per kilogram of product (ISO 14067 declared unit). Enter the product's weight for a per-item figure.
Country of manufacture not stated in the listing; India assumed.
m1: material matched from "cotton" (family, MEDIUM confidence): 'cotton' with no qualifier is treated as conventional (not organic or recycled).
Textile cutting and making loss 15 % of fabric input (PEF-style screening default), sent to landfill.
Packaging is not stated and no verified default exists for home textile, so it is excluded.
Yarn spinning: 1.176 kg fibre × Ring spinning (cotton, ~200 dtex) electricity: 3.4 kWh per kg yarn (van der Velden, Patel & Vogtlander, Int J LCA, 2014).
Weaving: 1.176 kg × Weaving (air-jet) electricity: 3.6 kWh per kg fabric (van der Velden et al., Int J LCA, 2014).
Dyeing & finishing: 1.176 kg × Dyeing & finishing (wet processing) energy: 7 kWh per kg fabric (electricity + thermal) (Quantis, Measuring Fashion, 2018 (dyeing & finishing = 36% of apparel GHG, largest stage)); thermal energy is modelled as grid electricity (no fuel split available).
Cutting and sewing: 1 kg × Cut-make-trim (garment assembly): 1 kWh per kg garment (Quantis, Measuring Fashion, 2018 (assembly ~7% of apparel GHG)); the garment cut-make-trim intensity is used for made-up home textiles.
Process energy is unmetered screening data (activity uncertainty GSD 1.5–2.0), on the IN grid.
Inbound transport of materials to the factory is left out of the total, because supplier locations are unknown; its likely size is estimated and reported under the cut-off rule below.
Distribution route is a screening default (1,000 km road), carrying product plus packaging.
Cut-off rule: processes are excluded only where no verified data exists, and each exclusion is estimated where possible and reported (ISO 14044 §4.2.3.3.3). Inbound transport is estimated at 0.0737 kg CO₂e.
Carbon content of cellulose computed from repeat-unit stoichiometry (0.4445 kgC/kg), pure polymer basis (additives, moisture and finishes ignored).
Secondary (library) factors are scored at least 3 on technology: PACT v3 Table 12 reserves scores 1-2 for primary data.
Aggregated secondary factors are used as published in their own GWP basis (AR5); only gas-split fuel factors and direct gas emissions are characterised with AR6. Residual inconsistency is typically a few percent for CO2-dominated factors.
Sources quoted as published figures (not open-licensed datasets): textile_exchange_2026. Replace with licensed or supplier data before external or comparative claims.
SensitivityThe figure with other published choices
Sensitivity analysis (ISO 14067 §6.4.5, §6.6)
The footprint recalculated with each alternative choice: other published factors, the other allocation method, the grid mix instead of a green-power contract, and the use profile at its uncertainty bounds. A large change shows where better data pays off first.
Line
Choice tested
Baseline
Alternative
Δ kg CO₂e
Δ %
Biodegradable Cotton (Cotton, conventional)
Emission factor
Conventional cotton lint, India country average
Conventional cotton fibre
ifeu (2022) Environmental footprints of cotton and cotton fibres
-1.729
-9%
Biodegradable Cotton (Cotton, conventional)
Emission factor
Conventional cotton lint, India country average
Conventional cotton fibre (TE/PE International 2014 comparison baseline)
Textile Exchange (2014) LCA of Organic Cotton Fiber, summary (PE International)
-2.779
-14.5%
Biodegradable Cotton (Cotton, conventional)
Emission factor
Conventional cotton lint, India country average
Conventional cotton fibre, global average
Cotton Incorporated LCA update (2017), as cited by ifeu 2022
-3.376
-17.6%
Biodegradable Cotton (Cotton, conventional)
Emission factor
Conventional cotton lint, India country average
Conventional cotton lint, global production-weighted average
Textile Exchange (2026) LCA for Cotton, technical report, Table 5-2 / Annex F
-1.494
-7.8%
Every line of the calculation6 lines: activity × factor, with sources
Full inventory
Footprint = Σ activity × emission factor
Every line: how much (activity) × how much CO₂e per unit (factor), with its source. Source labels
Screening carbon footprint shown on the Made for Planet catalogue so brands and buyers can see where a product's emissions come from. Reasons: No company data is available for this listing; a transparent estimate from the listing and published factors shows the likely size and the main stages. Audience: Brands and buyers (business-to-business). The estimate is also displayed on madeforplanet.com, labelled as a screening estimate; it is not an environmental claim the brand may use in marketing. Public comparative assertion: no.
Functional or declared unit and reference flow
§7.3 a
Declared unit: 1 kg (partial carbon footprint); reference flow 1 kg of product.
System boundary
§7.3 b
cradle to gate. Screening partial carbon footprint, cradle to gate, per kg: materials, fibre processing and making and packaging where known. Distribution, use and end of life are outside the boundary. Capital goods are excluded, as is usual for attributional product footprints. Stages modelled: raw_materials, production.
Significant unit processes
§7.3 c
cotton_fibre_conventional (virgin) (25.54 %); spinning: grid electricity IN (16.94 %); weaving: grid electricity IN (17.94 %); wet_processing: grid electricity IN (34.88 %)
Data sources
§7.3 d
LCA for Cotton, technical report Mar 2026; UK DESNZ Greenhouse gas reporting: conversion factors 2025 2025 (flat file); Carbon intensity of electricity (Ember via Our World in Data) 2026 release (2025 data)
Greenhouse gases considered
§7.3 e
CO₂, CH₄ (fossil and biogenic), N₂O and refrigerant gases (HFCs, SF₆, NF₃) where present; secondary factors cover the gases their publishers include.
Characterisation factors
§7.3 f
IPCC AR6 GWP100 with climate-carbon feedbacks; secondary factors in their published basis where no AR6 version exists (see gwp check).
Cut-off criteria and exclusions
§7.3 g, o
Inbound transport of materials to the factory: 0.073659 kg CO₂e (screening estimate: 1.176 kg of materials × 500 km by average lorry (UK DESNZ GHG conversion factors 2025, Freighting goods + WTT delivery vehicles); supplier locations are not known)
Allocation procedures
§7.3 h
No multi-output processes. Recycling: cut-off.
Timing of emissions
§7.3 i, 6.4.8
All emissions and removals counted as at the start of the assessment period; no delayed-emission weighting.
Data description and quality
§7.3 j
PACT Table 12 DQR: technological 3, geographical 1.02, temporal 1; per-line scores, confidence and 95 % uncertainty in the inventory.
Sensitivity and uncertainty
§7.3 k
4 sensitivity case(s); lognormal Monte Carlo on pedigree uncertainty.
Climate change only: other impacts (water, land, toxicity, biodiversity) are not assessed, so a lower footprint does not mean a lower environmental impact overall. Secondary factors limit accuracy as shown by the data-quality scores.
Value choices
§7.3 n
Cut-off for recycling (PACT); economic allocation only above a 5× value ratio; conservative factor where published values disagree (see sensitivity).
Scope changes and exclusions
§7.3 o
No product weight is stated, so the study is a partial carbon footprint per kg of product (cradle to gate): distribution, use and end of life are not quantified (ISO 14067 §6.3.3). Packaging is not stated and no verified default exists for this kind of product, so it is excluded without an estimate.
Life-cycle stages, use and end-of-life scenarios
§7.3 p, 6.3.7, 6.3.8
Not in scope (partial carbon footprint, cradle-to-gate).
2026-01-01 to 2026-12-31: current production as represented by the factor library (each factor's own data year is scored in the temporal data quality)
Product category rules
§7.3 s, 6.2
No product category rules conforming to ISO/TS 14027 are known for this product category; MFP screening rules are applied and disclosed.
Performance tracking
§7.3 t, 6.4.7
Not a performance-tracking study.
ISO 14067 counts biogenic removals (−1) and emissions (+1) in the carbon footprint; the PACT headline excludes biogenic uptake. Both are shown.
PACT v3 data and biogenic carbonData-exchange values and a downloadable file
PACT v3 data model (cradle-to-gate) and biogenic carbon balance
Download PACT v3.0.3 JSONProductFootprint in the Technical Specifications v3.0.3 format (decimals as strings). Check the conformance panel before sending it.
Footprint excl. biogenic uptake
19.2063 kg CO₂e
Footprint incl. biogenic uptake
17.2904 kg CO₂e
Fossil GHG emissions
19.1186 kg CO₂e
Land-use change GHG
—
Biogenic non-CO₂
0.0877 kg CO₂e
Biogenic CO₂ uptake
-1.9159 kg CO₂
Fossil carbon content
0.0000 kg C
Biogenic carbon content
0.4445 kg C
Aircraft GHG (no RF)
0.0000 kg CO₂e
Packaging GHG
0.0000 kg CO₂e
Exempted emissions
0.3820 %
Primary data share
0.0000 %
IPCC characterisation
AR6, AR5
Biogenic CO₂ uptake
-1.9159 kg CO₂
Biogenic CO₂ emitted
0.0000 kg CO₂
Biogenic C stored in landfill
0.0784 kg C
Biogenic C exported to recycling
0.0000 kg C
Biogenic C in product
0.4445 kg C
Engine / factor library
1.2.0 / 2026.11-mfp.8
RetroKitchen - Cellulose Dishcloth (Sheep) carbon footprint: 19.2 kg CO₂e per kg
